Check the compression and spark. If compression on that cylinder is flawed, that would also affect the crankcase pressure that forces fuel to that cylinder.

The spark (with plugs removed) should jump a 7/16" gap with a strong blue lightning like flame... a real SNAP! The gap is important.

In cleaning the carburetor.... If you did not remove the brass high speed jet that's located horizontally in the bottom center of the float chamber to manually and carefully clean it with a piece of single strand steel wire... do so as solvent alone just doesn't do that job properly. Also keep in mind that floating debris (fuel lines breaking apart, etc) will easily be drawn down to clog that jet. Fuel must flow freely through that jet before it gains access to any other passageway.

Check also that the carburetor is actually having fuel delivered to that float chamber... no intermittent clogs, float needle valve jams, etc.

The four reeds that you mention being open 1/8".... that is a happening that's unheard of. I've not encountered that in my 30+ years experience... one leaf/reed maybe due to something getting drawn in and caught... BUT... four with nothing holding them open indicates something not as it should be. And it should be impossible to simply press them back into shape.

If it were me, I'd take that reed plate apart and at a minimum flip that leaf valve over so that it shuts properly.

Note that I retired in 1991 so various areas of your 98 model would be foreign to me but the fuel delivery procedure would be the same.

Compression on that cylinder is 123psi and other three are at 125. Have a spark checker and spark will jump a 3/4 inch gap. Strong blue bolt. Ive had the carbs off 3 times making sure everything was clear, shot compressed air through the bottom jet as i dont have a flat blade screwdriver small enough to remove the jet but will be buying one today. New fuel lines from gas tank to cone filter located in the motor. I wish i could upload a pic of the reeds but the site i was using wants me to buy a subscription at the cost of 400 a year. Do you use a site to upload pics. While i had everything off i should have cleaned the whole fuel system. Thank you sir for the reply. Im going to try to find a site that will let me upload pics. I have pics of the reeds and video of the spark jumping the gap.

Two others are open that you cant see in pic.

Join "Photobucket" a free site to upload all your pictures, and from there you can transfer your pictures anywhere, including here. The free portion is sufficient, but if not, you can also subscribe for $25 per year. Look it over.

Yes sir, I was using photobucket until yesterday. Tried uploading a picture and was rerouted to a page saying i had to buy a subscription at the cost of $400 a year. I didnt see the part where you could pay monthly but will go back and check it out.
About those reeds, you said before the pic that youve never seen that problem before. After seeing the picture, what do you believe would have caused it? Im going to flip them as you suggested just curious to know what you think of it. Couldn't find the video of the spark but will get one when i get off work and upload it. Ive also moved coils around, put bottom on top and it didnt help.

Also is there anything you would recommend putting in the cylinder to keep it lubed while im running my tests?

Are you saying that it was "Photobucket" who was going to charge $400 per year... OR... some other site that you were transferring a picture to?

Also, I didn't say anything about a monthly method of payment... where did that come from? The $25 charge I'm sure you know is a annual fee.

I've received no pictures from you on this site so far.

Lube for cylinders while running tests.... the present mixture in the cylinders should be sufficient. There's still plenty in the crankcase that the pistons would still be drawing on.

The one of the reeds at 11:11am didnt show up? I see it on my end. And yes sir, yesterday on another forum when i tried to post a picture photobucket rerouted me to a subscription page that said annual cost was $400 annually.

Did it show up that time?

Yes, but it was so large that I had no idea what I was looking at. I usually resize my pictures so that the pixel width is somewhere between 600 and 1000.

Ive got to figure out how things work on this forum and we must not be seeing the same thing. The second pic i uploaded, seems to be the first pic you've saw, is actually very small on my end. From what you can tell from the pic, do you think that has anything to do with my problem?